Leak Detection and Repair Hinesville GA done right the first time
We find hidden leaks fast and fix them before damage spreads
When water shows up where it shouldn't, our Leak Detection and Repair Hinesville GA team traces it to the source and stops it. We handle slab leak detection in Hinesville, pinhole copper failures, and supply line breaks in homes from Bradwell to Riverwalk. Call (912) 296-2269 and we'll pinpoint the leak, explain the fix, and get your floors dry again.
Leak Detection and Repair Hinesville GA explained
Leak Detection and Repair Hinesville GA is the process of locating hidden water loss in your plumbing system and fixing it at the source, rather than guessing and tearing into walls. We use acoustic listening discs, thermal imaging, and pressure gauges to isolate the exact failure point, then repair copper pipe, PEX pipe, or PVC pipe with the right fittings, solder, and Teflon tape. Most hidden leaks are found in under two hours.
Hinesville homes sit on slab foundations and clay-heavy soil, and both push back on plumbing. A slow slab leak can run for weeks before you notice a warm spot on the floor or a jump in your water bill. If you've been searching for water leak detection in Hinesville, we can usually be at your door the same day, confirm the leak, and give you a straight answer on repair.
Why Hinesville homeowners call us first
Hidden leaks cost Hinesville homeowners hundreds in wasted water and thousands in structural damage. We stop the loss early, fix it properly, and leave you with proof the line holds pressure.
Stop damage early
A pinhole leak in a copper pipe can push 50 to 200 gallons a day into your slab or crawlspace. We isolate it in one visit, so you avoid buckled flooring, stained ceilings, and mold remediation that runs $2,000 or more. Catching it in week one instead of month two changes the whole bill.
Lower water bills
Most Hinesville households see a $30 to $90 monthly jump when a leak is running. Once we complete water leak detection in Hinesville and repair the line, that charge disappears. We show you the meter reading before and after so you can see the difference yourself.
Non-invasive locating
We don't open drywall to hunt. Leak detection equipment, thermal cameras, and a sewer camera let us mark the spot on the floor with tape before any cutting starts. That means one small access point instead of three exploratory holes across your living room.
Repairs that hold
We cut out the failed section and rebuild it with SharkBite or Uponor fittings, proper solder joints, and pressure-tested connections. Every repair gets a pressure gauge test at 80 PSI before we pack up. You get a dry floor and a line that passes inspection.
How our leak detection process works
Five steps, one visit in most cases. You'll know what we found, what it costs, and when it's fixed before we start cutting anything.
Phone triage
You call (912) 296-2269 and describe what you're seeing: a warm floor spot, a spinning meter, a water bill spike, or a damp baseboard. We ask a few questions, give you a realistic arrival window, and tell you how to shut off the main if water is actively running. Most calls get a same day Leak Detection and Repair Hinesville GA appointment.
Pressure test
We isolate the system and pressurize it with a gauge to confirm there's a real leak and how fast it's losing pressure. This takes 20 to 30 minutes and tells us whether the loss is on the supply side, the drain side, or the irrigation line. No guessing, no exploratory demolition.
Pinpoint the leak
Acoustic listening equipment, thermal imaging, and a sewer camera narrow the location down to a few inches. For slab leak detection in Hinesville, we map the line under the floor and mark the access point with tape. You see exactly where we're going to work before we touch a pipe cutter.
Repair the line
We cut out the damaged section and replace it with copper pipe or PEX pipe, matching the existing material and code requirements. Fittings get soldered or crimped with a PEX crimping tool, sealed with pipe dope or Teflon tape, and torqued to spec. A straightforward under-slab repair runs two to four hours.
Test and verify
We re-pressurize the system to 80 PSI, hold it, and watch the gauge. Then we run every fixture in the house, check the meter, and confirm the reading has stopped climbing. You get a walkthrough of the repair, photos of the work, and a written warranty before we leave.
Local leak detection experience you can use
Our technicians hold Georgia State Plumbing License credentials and work under Uniform Plumbing Code and International Plumbing Code standards on every job. We've traced leaks in slab foundations, pier-and-beam crawlspaces, and 1970s copper systems across Liberty County. We keep leak detection equipment, pipe cutters, soldering torches, and PEX crimping tools on every truck, so most repairs finish in one trip. When a line is too far gone to patch, we tell you straight and walk you through repiping options.
- State-licensed plumbing contractor with Master Plumber License and Journeyman Plumber License holders on staff.
- Backflow Prevention Certification for supply-side work and cross-connection testing.
- OSHA Safety Certification on every technician working under a home or in a crawlspace.
- Trained on Rheem, Navien, Rinnai, Bradford White, and A.O. Smith systems where leaks tie into water heaters.
- Experienced with Moen, Delta, Kohler, and American Standard fixtures and supply lines.
Why our Leak Detection and Repair Hinesville GA stands out
We're a local crew, not a call center. You get a licensed plumber, a clear price, and a repair that gets tested before we leave your driveway.
Same-day response
Most Leak Detection near me Hinesville calls get a technician the same day, and active flooding gets priority. We stock copper pipe, PEX pipe, CPVC pipe, fittings, and SharkBite push fittings on every truck so we're not making a parts run while your floor soaks.
Upfront pricing
You get the detection fee and the repair range before we start. A standard leak detection runs $150 to $350, and most repairs land between $250 and $1,200 depending on access and pipe material. No surprise line items when the invoice arrives.
Real diagnostic tools
We carry acoustic listening discs, thermal cameras, pressure gauges, and a sewer camera. That's how we find a slab leak in Hinesville GA without tearing up half your hallway. The equipment pays for itself in the drywall you don't have to replace.
Work that passes inspection
Every repair is built to Uniform Plumbing Code and International Plumbing Code standards, pressure-tested at 80 PSI, and backed by a written warranty. If you're selling the house, our documentation gives the buyer's inspector something concrete to review.
What our leak detection service includes
Every leak call starts with a full diagnostic and ends with a pressure test. Here's what's covered in a standard visit, and what we handle as an add-on when the repair turns out to be bigger than expected.
What's Included
Full system pressure test
We isolate the supply and drain sides, pressurize the system, and watch a gauge to confirm the leak and measure how fast it's losing pressure. This takes 20 to 30 minutes and tells us exactly which side of the plumbing is failing.
Acoustic and thermal locating
Listening discs and a thermal camera narrow the leak down to a few inches. For slab leak detection in Hinesville, we map the line under the floor and mark the access point with tape before any cutting begins.
Sewer camera inspection
When the symptoms point to the drain side, we run a sewer camera through the line to check for cracks, root intrusion, or shifted pipe. It's the fastest way to rule out a drain leak before we commit to a supply-side repair.
Pipe repair or section replacement
We cut out the failed section and rebuild it with copper pipe, PEX pipe, or CPVC pipe, using proper fittings, solder, and Teflon tape. Most repairs finish in two to four hours, including the test.
Post-repair verification
We re-pressurize to 80 PSI, hold it, run every fixture, and check the meter to confirm it's stopped climbing. You get photos of the repair and a written warranty before we pack up the truck.
Leak problems we solve in Hinesville
Most leaks we find in Hinesville fall into five categories. Each one gets worse and more expensive the longer it runs, so we treat every call as time-sensitive.
Water bill spiked with no visible leak
A hidden leak can waste 50 to 200 gallons a day and add $30 to $90 to your monthly bill. Left alone for months, it undermines the slab or subfloor underneath.
We pressure-test the system, use acoustic and thermal equipment to locate the loss, and repair the line the same visit in most cases. You see the meter reading before and after so you know the leak is gone.
Warm spot or damp patch on the floor
A warm spot usually means a hot water line is leaking under the slab. The heat accelerates damage to flooring, and the moisture feeds mold that can cost thousands to remediate.
We confirm it's a slab leak with thermal imaging, mark the exact location, and open one small access point instead of several. Then we repair the copper or PEX line and pressure-test it at 80 PSI.
Musty smell or stained baseboards
Musty odors and dark baseboard stains mean moisture has been sitting behind the wall or under the floor for a while. Drywall, insulation, and framing start to rot, and the repair bill climbs fast.
We trace the moisture back to the source, repair the failed pipe or fitting, and verify the line holds pressure. If the damage is cosmetic, we tell you what to dry out and what to replace.
Meter spinning with everything off
If the meter keeps moving with every fixture shut off, water is escaping somewhere in the system. It could be a supply line, an irrigation line, or a slab leak, and it won't stop on its own.
We isolate sections of the system one at a time until the meter stops, which tells us exactly where the leak is. Then we repair that section and re-test to confirm the meter is still.
Low water pressure plus a damp spot
Low pressure combined with moisture usually means a leaking or partially blocked line. It can also point to a failing shut-off valve or a corroded galvanized pipe that's about to fail completely.
We check the pressure gauge at multiple fixtures, inspect the shut-off valves, and camera the line if needed. Then we repair or replace the failing section and confirm pressure is back to normal before we leave.
When to call for leak detection
You got a water bill that's $40 higher than last month and nothing in the house is running.
We pressure-test the system, isolate the supply and drain sides, and use acoustic equipment to find the loss. Most hidden leaks are located in under two hours, and we repair them the same visit when parts allow.
Your bill returns to normal the next cycle, and you have a pressure-tested repair with a written warranty.
There's a warm spot on the floor near the hallway and the tile feels loose.
That's a classic slab leak signature. We confirm it with thermal imaging, mark the line under the slab, and open one small access point. Then we replace the failed copper or PEX section and pressure-test at 80 PSI.
The floor stops heating up, the moisture source is gone, and you avoid tearing up the whole hallway.
You're buying a Hinesville home and the inspector flagged moisture near the foundation.
We run a full leak detection inspection, pressure-test the supply lines, and camera the drains. You get a written report with photos and pressure readings that you can hand to your realtor or the seller.
You know exactly what you're buying, and you have documentation to negotiate repairs or walk away.
Your water heater is dripping and you can't tell if it's the tank or the supply line.
We isolate the water heater, check the fittings, the anode rod, and the supply lines, and trace the moisture to its source. If the tank is failing, we quote replacement. If it's a fitting, we repair it on the spot.
You get a straight answer on repair versus replace, and the drip stops either way.
Tools and methods we use
Tools & Equipment
Acoustic listening equipment
Picks up the sound of water escaping under pressure, which lets us narrow the leak location down to a few inches without opening walls or floors.
Thermal imaging camera
Shows temperature differences on floors and walls, which is how we spot a hot water slab leak as a warm patch before any concrete gets cut.
Pressure gauge
Confirms the leak exists, measures how fast the system loses pressure, and verifies the repair holds at 80 PSI before we leave.
Sewer camera
Lets us inspect the inside of drain lines for cracks, root intrusion, and shifted pipe so we can rule out drain-side leaks.
PEX crimping tool and soldering torch
Used to rebuild the failed section with PEX pipe or copper pipe, depending on what the existing line is made of and what code requires.
Pipe cutter and tube bender
Gives us clean cuts and precise bends so the new section fits without stress on the joints, which is where most repeat leaks start.
Methods
Isolation pressure testing
We close off sections of the system one at a time and watch the gauge. When the pressure holds, we've found the leaking section. This method is how we avoid exploratory demolition and keep the repair focused.
Uniform Plumbing Code compliance
Every repair is built to Uniform Plumbing Code and International Plumbing Code standards, including proper materials, support spacing, and joint methods. That matters if you ever sell the home or need an inspection.
Post-repair pressure verification
We re-pressurize to 80 PSI, hold it, run every fixture, and check the meter. If the gauge moves or the meter climbs, we're not done. You see the test results before we pack up.
Material-matched repair
We match the repair to the existing pipe: copper pipe with soldered joints, PEX pipe with crimp or SharkBite fittings, or CPVC pipe where appropriate. Mixing materials incorrectly causes electrolysis and repeat failures.
How leak detection runs in Hinesville
Hinesville sits on clay-heavy soil and slab foundations, and that combination drives most of the leaks we see. Clay expands and contracts with our wet winters and hot summers, shifting the ground under the slab and stressing copper pipe until it cracks. Homes built in the 1960s and 1970s often still have original copper or galvanized lines that are past their service life. Newer builds in Cypress Cove and Riverwalk use PEX pipe, which handles movement better but still fails at poorly crimped fittings. Hard water in Liberty County adds scale inside the pipe, narrowing the diameter and raising pressure at the joints. When you call for water leak detection in Hinesville, we start with a pressure test, then use acoustic and thermal equipment to pinpoint the loss. For slab leak detection in Hinesville, we map the line under the floor and cut one access point instead of several. We work to Uniform Plumbing Code and International Plumbing Code standards, and we pressure-test every repair at 80 PSI before we leave.
Service Areas
Older homes with original copper and galvanized lines. Pinhole leaks and failing shut-off valves are the most common calls we get here.
A mix of slab and pier-and-beam construction. Slab leaks show up as warm floor spots, while pier-and-beam homes leak into the crawlspace where it's harder to spot.
Newer construction with PEX pipe. Most leaks trace to crimp fittings or supply lines behind appliances rather than the pipe itself.
1970s ranch homes with thin-wall copper. These lines are prone to pinhole failures, especially where they pass through the slab.
Newer builds with irrigation systems. We frequently find irrigation line leaks that homeowners mistake for indoor plumbing problems.
Local Considerations
Clay soil expansion and contraction
Seasonal ground movement stresses under-slab copper pipe and causes cracks at joints. This is the leading cause of slab leaks in Hinesville.
Hard water in Liberty County
Scale builds up inside copper and PEX lines, narrowing the diameter and raising pressure at fittings. It shortens the life of water heaters and supply lines.
Hot, humid summers
High humidity makes it harder to spot slow leaks because condensation looks like moisture. We rely on pressure testing and thermal imaging rather than visual inspection alone.
Older housing stock near Downtown
Original galvanized and copper lines from the 1960s and 1970s are past their expected service life. We see repeat leaks in these homes and often recommend repiping.
Slab leak under a Bradwell hallway
A Bradwell homeowner noticed a warm spot on the hallway floor and a water bill that had climbed $65 in one month. Two other companies had looked and couldn't find the source without opening the floor.
We pressure-tested the system, confirmed a hot water slab leak with thermal imaging, and marked the line. One small access cut, a two-foot copper section replaced, and an 80 PSI test that held. The bill dropped back to normal the next cycle.
Maintenance & Follow-up
Keep an eye on the meter for the first month and note any new warm spots. We recommend a water softener to slow scale buildup in the copper line.
A Griffin Park home had a musty smell in the laundry room and a dark stain spreading across the baseboard. The copper supply line behind the wall had a pinhole leak that had been running for weeks.
We isolated the line, cut out the failed section, and replaced it with new copper pipe and soldered fittings. The wall was opened at one point, the repair was pressure-tested at 80 PSI, and the moisture source was eliminated.
Maintenance & Follow-up
Let the wall cavity dry completely before patching. We checked the rest of the copper in the house and flagged two more sections to watch.
A Riverwalk homeowner's meter kept spinning even with the house shut off. They assumed it was a slab leak and were bracing for a major repair.
We isolated the irrigation zone and found a cracked fitting at a valve box. The repair took under an hour and cost a fraction of a slab repair. The meter stopped moving immediately after the fix.
Maintenance & Follow-up
Check irrigation valve boxes each spring for cracks and loose fittings. A $20 fitting now saves a $2,000 landscape repair later.
How much does Leak Detection and Repair cost in Hinesville GA?
Most Hinesville homeowners pay $150 to $350 for detection and $250 to $1,200 for the repair, so a typical total lands between $400 and $1,500 in 2026. Slab leaks and under-foundation access push toward the higher end because we cut and patch concrete. Simple supply line or fixture leaks stay on the low end. We quote the detection fee and the repair range before we start.
How do I know if I have a hidden water leak in Hinesville?
The four clearest signs are a water bill that jumped $30 or more, a meter that keeps spinning with every fixture off, a warm or damp spot on the floor, and the sound of running water when nothing is on. Musty odors near baseboards and hairline cracks in drywall count too. If two or more show up, call us for water leak detection in Hinesville Georgia before the damage spreads.
Who does water leak detection near me in Hinesville Georgia?
We do. Hinesville Plumbing Repair handles water leak detection and repair across Liberty County, including Downtown Hinesville, Bradwell, Liberty Woods, Griffin Park, and Riverwalk. Call (912) 296-2269 and we'll schedule a visit, usually the same day. We serve ZIP codes 31313 and 31310 and the surrounding Liberty County area.
Can you find a slab leak in Hinesville GA without breaking my floor?
Yes. We use acoustic listening equipment and thermal imaging to pinpoint the line under the slab, then mark the exact spot before any concrete is opened. That usually means one small access cut instead of several exploratory holes. Once we confirm the location, we repair the copper or PEX line, pressure-test it, and patch the floor.
Licensed, tested, and accountable
Certifications
Reviews
Found a slab leak two other plumbers missed. They used thermal imaging, marked the spot, and had it repaired the same day. Pressure-tested it in front of me and showed me the gauge. Fair price and no mess left behind.
Called about a water bill that doubled. They came out the same afternoon, pressure-tested everything, and found a pinhole leak in the laundry room wall. Repair was done in a couple of hours and the bill went back to normal.
Professional from the first phone call. They explained the detection fee upfront, found the leak under the kitchen slab, and gave me a clear price for the repair. Tested it at 80 PSI before leaving. Would use them again.
We had a musty smell and couldn't figure out where it was coming from. Their technician traced it to a leaking supply line behind the baseboard, fixed it, and checked the rest of the plumbing while he was there. Honest and thorough.
Related Services
Emergency Plumbing Repair
When a leak turns into active flooding, emergency plumbing repair stops the water first. We shut off the line, contain the damage, and then run full leak detection once the immediate crisis is handled. Call (912) 296-2269 any time.
Emergency Plumbing RepairDrain Cleaning
A clogged drain and a hidden leak can look alike from the surface. We clear the line with a drain snake or hydro-jetter, then pressure-test to confirm the pipe isn't cracked. Root intrusion in older Hinesville sewer lines is a common culprit.
Drain CleaningWater Heater Repair
A leaking water heater often mimics a supply line leak. We check the tank, fittings, and anode rod, then trace any moisture back to its source. Rheem, Bradford White, and A.O. Smith units are what we see most in Hinesville homes.
Water Heater RepairWater Heater Installation
New water heater installs get fresh supply lines, shut-off valves, and a pressure test before we call it done. If your old unit leaked and damaged the surrounding piping, we repair that at the same time so you're not scheduling two visits.
Water Heater InstallationTankless Water Heater Repair
Navien and Rinnai tankless units develop scale and connection leaks that show up as drips under the cabinet. We isolate the leak, descale the unit, and repair the fittings. Hard water buildup in Liberty County makes this a regular call.
Tankless Water Heater RepairTankless Water Heater Installation
Tankless installs require new gas, water, and venting connections, and every one gets pressure-tested. If your existing line has a slow leak, we fix it during the install instead of leaving it buried behind the new unit.
Tankless Water Heater InstallationPipe Repair
Pipe repair is the second half of leak detection. Once we know where the failure is, we cut out the bad section and rebuild it with copper pipe, PEX pipe, or CPVC pipe, using proper fittings and solder. Most repairs finish in two to four hours.
Pipe RepairPipe Replacement
When a line has three or more leaks, patching stops making financial sense. Pipe replacement swaps the whole run for new copper or PEX. We pressure-test the new line at 80 PSI and document it for your records.
Pipe ReplacementRepiping
Older Hinesville homes with failing galvanized or thin copper lines often need whole-house repiping. We map the existing system, run new PEX or copper, and test every fixture. It's a bigger job, but it ends the cycle of repeat leaks.
RepipingFaucet Repair
A dripping Moen or Delta faucet wastes water and can hide a supply line leak behind the wall. We replace cartridges, O-rings, and supply lines, then check the shut-off valves while we're under the sink.
Faucet RepairFaucet Installation
New faucet installs get fresh supply lines and Teflon tape on every threaded connection. We pressure-test after install, so a brand-new fixture never becomes the next leak call.
Faucet InstallationToilet Repair
A running toilet can waste 200 gallons a day and throw off your leak diagnosis. We replace flappers, fill valves, and wax rings, then confirm the toilet isn't masking a larger supply-side leak.
Toilet RepairToilet Installation
Toilet installs include a new wax ring, supply line, and shut-off valve. We test the seal and the fill line before we leave, so you're not chasing a phantom leak a week later.
Toilet InstallationShower Repair
Shower leaks often show up as stained ceilings below or loose tile. We check the valve, the drain connection, and the supply lines behind the wall, then repair the source instead of just caulking over it.
Shower RepairShower Installation
New shower installs get pressure-tested connections and a drain check before the wall closes up. If we find a hidden leak during the rough-in, we fix it while everything is still accessible.
Shower InstallationBathtub Repair
Tub leaks usually trace to the overflow gasket, drain shoe, or supply lines. We isolate the source, replace the failed parts, and confirm the repair holds before sealing anything back up.
Bathtub RepairBathtub Installation
Bathtub installs involve drain, overflow, and supply connections that all need testing. We pressure-test the supply side and water-test the drain so a new tub doesn't become a ceiling stain downstairs.
Bathtub InstallationSink Repair
Kitchen and bath sink leaks are often supply line or drain basket failures. We tighten or replace the connection, check the shut-off valves, and confirm the cabinet floor stays dry.
Sink RepairSink Installation
Sink installs get new supply lines, a fresh drain assembly, and pipe dope on threaded joints. We run water through the system and check underneath before calling the job complete.
Sink InstallationGarbage Disposal Repair
A jammed or leaking disposal can drip into the cabinet and look like a supply leak. We clear the jam, reseal the mount, and check the drain connection for cracks.
Garbage Disposal RepairGarbage Disposal Installation
New disposal installs include a fresh mount, plumber's putty, and a drain line check. We run the unit and inspect underneath so a loose connection doesn't leak into your cabinet.
Garbage Disposal InstallationSewer Line Repair
Sewer leaks and water leaks get confused all the time. We camera the line, locate the break, and repair it. Root intrusion and shifted clay pipe are the two most common causes in older Hinesville neighborhoods.
Sewer Line RepairSewer Line Replacement
When a sewer line has collapsed or bellies, replacement beats patching. We run new PVC pipe, set the fall correctly, and test the line before backfilling. Permits and inspections are handled as part of the job.
Sewer Line ReplacementSewer Camera Inspection
A sewer camera inspection shows us exactly what's happening inside the pipe. We use it to rule out drain-side leaks before committing to a supply-side repair, and to document root intrusion or cracks for your records.
Sewer Camera InspectionSump Pump Repair
A failing sump pump lets groundwater rise into your crawlspace and can mimic a plumbing leak. We test the float, check the discharge line, and repair or replace the pump so the space stays dry.
Sump Pump RepairSump Pump Installation
New sump pump installs include a check valve, discharge line, and a test run. We confirm the pit drains properly so groundwater never gets mistaken for a slab leak again.
Sump Pump InstallationWater Softener Installation
Hard water in Liberty County eats copper pipe from the inside. A water softener reduces scale buildup and extends the life of your lines. We install the unit and pressure-test every connection.
Water Softener InstallationWater Softener Repair
A leaking softener or failed bypass valve can drip constantly and drive up your bill. We repair the unit, check the resin tank, and confirm the supply lines aren't losing pressure.
Water Softener RepairWater Filtration System Installation
Whole-home filtration installs add connections that need to be leak-free. We install the system, pressure-test the new lines, and check the existing plumbing while we're in the crawlspace or utility room.
Water Filtration System InstallationWhat Hinesville homeowners say
Real experiences from customers who chose our Leak Detection and Repair services
"Our water bill jumped almost $70 and I couldn't find anything wet. They came out the same day, pressure-tested the system, and found a slab leak under the hallway with thermal imaging. Marked the spot, cut one small section, replaced the copper, and tested it at 80 PSI. Bill went back to normal the next cycle."
Marcus T.
Homeowner, Bradwell
"We had a warm spot on the kitchen floor for weeks and kept putting it off. Their technician showed up, confirmed it was a hot water line leak, and had it repaired in about three hours. He showed me the pressure gauge before and after and walked me through the warranty. No mess left behind."
Denise R.
Homeowner, Griffin Park
"I manage several rentals in Liberty County and use them for leak calls. They camera the line, tell me whether it's a drain or supply issue, and give me a straight price before starting. Last month they found a pinhole leak in a copper line that two other companies missed. Fast, clean work."
Raymond K.
Property Manager, Downtown Hinesville
Need Leak Detection and Repair Hinesville GA today?
We're licensed, local, and stocked with the parts to fix most leaks in one visit. Call (912) 296-2269 and we'll trace the leak, quote the repair, and pressure-test the line before we leave.